Written by Diane Watkins; Updated December 29, 2018![Bosch Washing Machine Problems Bosch Washing Machine Problems](/uploads/1/2/6/0/126079363/568175022.jpg)
![Clothes Clothes](/uploads/1/2/6/0/126079363/167482811.jpg)
Related Articles
- 1 What Happens When a Washing Machine Is Off Balance?
- 2 Troubleshoot Clothes Washer Problems
- 3 Troubleshooting Dryer Noises
- 4 Troubleshooting Noisy Kenmore Washers
The washer door won’t unlock! This is a problem most commonly found in front loaders, as top loaders don’t need to lock their doors to keep water inside. Front loaders need to stay tightly sealed during operation. It’s not until the end of the wash cycle that the machine will unlock automatically. Washing machine will not drain or is noisy on drain. Generally this will be some sort of drain pump failure or blockage, see video for more help on this. Drain pump blocked. Drain pump faulty. Waste outlet hose blocked. Sump hose blocked. Object in pump (coin, screw, baby sock ETC) Poor flooring or installation. Considering all the possible failures of Bosch washing machines, we can enumerate the most typical ones: The washer won’t heat the water during a washing cycle. The washer won’t drain. The tub won’t spin. The drum makes some noise. The washer won’t get any water. The motor won’t run.
Google software engineer interview questions. A washer that is off balance during the spin cycle makes a lot of noise. Worse, overbalanced loads can actually damage the machine. The problem can have a variety of causes. Try the easier solutions first before taking apart the washing machine.
For this test we will use the famous “” wordlist.DISCLAIMER: This software/tutorial is for educational purposes only. It should not be used for illegal activity. Wpa wpa2 wordlist download. Then converted to the right format depending on the captured method and moved over to the Windows client to be cracked.Use the guides and to capture the WPA2 handshake.
Remove Shipping Materials
If your washer is new and the problem started immediately, it is likely caused by shipping materials accidentally left in place. On a top-loading washer, a shipping bolt is installed on the bottom center of the washer. Top-loading washers also typically have three shipping bolts, spacers and metal clamps in the back of the washer. Some models may have even more shipping materials that need to be removed. Refer to the installation instructions for your washer and make sure all shipping materials have been removed before using the machine. Failure to remove these shipping materials causes problems with the spin cycle, and it can also damage the machine permanently.
![Bosch Washing Machine Problems Bosch Washing Machine Problems](/uploads/1/2/6/0/126079363/568175022.jpg)
Level the Machine
Check that the machine is level across the front, back and sides. A machine that is not level will rock during the spin cycle and cause the machine to be off balance. All four legs should be in firm contact with a solid floor. A carpeted surface can throw this balance off. If your washer is located on a pedestal, the problem can be amplified. Top-loading washers automatically adjust to level. If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it. You may need to open the front access panel to loosen the lock nuts that control the legs.
Check for Overloading
If you tend to fill the washer completely to the top, regardless of the weight or composition of the contents, you may be overloading your machine. An easy way to check this is to run a small load. If you have no problems with a small load, consider that overloading may be causing your spin cycle balance problem.
Look for Laundry Caught Below the Tub
Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing. If you cannot see a problem, you may need to remove the front or top panel and the agitator. Remove the offending item and clean out any debris. Replace the agitator and panel before running the machine again.
About the Author
Diane Watkins has been writing since 1984, with experience in newspaper, newsletter and Web content. She writes two electronic newsletters and has a Bachelor of Science degree in chemistry from Clemson University. She has taken graduate courses in biochemistry and education.
Cite this Article Choose Citation Style
Watkins, Diane. 'What to Do if a Washer Is Off Balance During the Spin Cycle With Every Load.' Home Guides | SF Gate, http://homeguides.sfgate.com/washer-off-balance-during-spin-cycle-load-100979.html. 29 December 2018.
Watkins, Diane. (2018, December 29). What to Do if a Washer Is Off Balance During the Spin Cycle With Every Load. Home Guides | SF Gate. Retrieved from http://homeguides.sfgate.com/washer-off-balance-during-spin-cycle-load-100979.html
![Clothes Clothes](/uploads/1/2/6/0/126079363/167482811.jpg)
Watkins, Diane. 'What to Do if a Washer Is Off Balance During the Spin Cycle With Every Load' last modified December 29, 2018. http://homeguides.sfgate.com/washer-off-balance-during-spin-cycle-load-100979.html
Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name.
The impeller housing was kind of grundgey so I cleaned it. I found I had to stick a towel into the sump while I cleaned because water was still puddling at the bottom.
Most of the dirt came off with direct scrub with an old toothbrush. But there was some resistant scale that responded to the pointed end of a nail.
Most of the dirt came off with direct scrub with an old toothbrush. But there was some resistant scale that responded to the pointed end of a nail.
Bosch Washing Machine
Update 8/2016 White vinegar is often used on stubborn deposits, Sometimes a spray works, sometimes you need a soaking. There are specific mineral-deposit-cleaning products if your water is particularly mineral laden.
The impeller housing is marked to indicate which way goes down. Align the housing and screw the cover back in. I did not see any kind of thread lube / sealant, so I did not apply any. Usually sealants are not used on plastic. However, sometimes there is silicone grease on o-rings. If your model had grease, reapply a little bit if you wiped it off during cleaning or during removal.
Insert the cover and screw it down hand tight. Run the short cycle to check for leaks.
Reattach the access panel.
Smile because you just saved at least $50 on a service call. Now pay it forward and bless someone.
The impeller housing is marked to indicate which way goes down. Align the housing and screw the cover back in. I did not see any kind of thread lube / sealant, so I did not apply any. Usually sealants are not used on plastic. However, sometimes there is silicone grease on o-rings. If your model had grease, reapply a little bit if you wiped it off during cleaning or during removal.
Insert the cover and screw it down hand tight. Run the short cycle to check for leaks.
Reattach the access panel.
Smile because you just saved at least $50 on a service call. Now pay it forward and bless someone.